Free CWDP-305 sample questions
The free CWDP-305 sample questions on this page have answers and explanations for every item. They cover requirement gathering, channel planning and coverage checks after an install. Treat them as a quick test of your design thinking.
Try them in the simulator Same questions, with study, timed and flashcard modes.
Showing 10 of 20 free sample questions.
After deploying a new WLAN, a validation survey is performed. The designer compares the predictive survey results from the planning phase with the actual post-deployment survey results. The actual coverage shows significant deviations from the predictive model in several key areas. What is the most common reason for such a discrepancy?
A university is experiencing issues with VoWiFi calls dropping as users walk between two academic buildings connected by an outdoor courtyard. A post-deployment survey confirms adequate signal strength (-65 dBm or better) from both buildings' APs throughout the courtyard. Analysis of client roaming behavior shows that devices are remaining associated with the AP in the first building until the signal drops to -80 dBm before roaming to the much stronger AP in the second building. This phenomenon is known as:
Case Study: Manufacturing Plant Optimization A large manufacturing plant recently deployed a new Wi-Fi 6 network. Post-deployment validation testing reveals several critical issues. The plant floor is a challenging RF environment with metal machinery, moving gantries, and high levels of 2.4 GHz interference from industrial equipment. Validation Findings: An active validation survey was performed. In the parts assembly area, throughput tests consistently fail to exceed 50 Mbps, despite excellent signal strength (-55 dBm). Spectrum analysis in this area shows a high noise floor at -70 dBm in the 2.4 GHz band and a clean 5 GHz band. In the packaging area, VoWiFi calls have poor quality with robotic-sounding audio, and roaming tests show devices are slow to handoff between APs. The current design uses omnidirectional APs mounted at 30 feet, with transmit power set to maximum on all APs. Requirements: The assembly area requires a minimum of 100 Mbps throughput for data-intensive tablets. The packaging area requires MOS scores of 4.0 or higher for VoWiFi calls and seamless roaming for handheld scanners. The plant manager has rejected any solution that involves running new cable drops. Which combination of remediation actions will most effectively address all the identified issues?
To ensure a new WLAN design for a hospital meets the stringent requirements for Voice over Wi-Fi (VoWiFi), which performance metric is most critical to measure during the application testing phase?
A consultant is creating the final 'as-built' documentation after a successful WLAN deployment and validation project. Which of the following elements are ESSENTIAL to include in this documentation? (Select THREE)
True or False: A passive survey is the most effective method for validating client roaming performance and application throughput.
A wireless engineer is designing a network for a convention center. The primary requirement is to handle extremely high client density in the main exhibition hall. Which two 802.11ax (Wi-Fi 6) features are most critical for improving spectral efficiency and performance in this specific scenario? (Select TWO)
A large enterprise is designing a WLAN with a requirement for Zero Trust security. A key principle of their strategy is micro-segmentation, where each wireless client is isolated and cannot communicate with any other wireless client on the same VLAN/subnet unless explicitly permitted by a policy. Which feature must be enabled on the WLAN controller and APs to enforce this?
You are performing a validation survey of a newly installed WLAN. The diagram below shows a simplified floor plan with the final AP placement and a heat map visualizing the Signal-to-Noise Ratio (SNR). Based on the heat map, which area requires remediation? graph TD subgraph Floor Plan A[AP1] -- "Coverage" --> Z1((Zone 1)) B[AP2] -- "Coverage" --> Z2((Zone 2)) C[AP3] -- "Coverage" --> Z3((Zone 3)) Z1 -- "Overlap" --> Z2 Z2 -- "Overlap" --> Z3 end subgraph SNR Heat Map style Z1 fill:#7CFC00,stroke:#333,stroke-width:2px style Z2 fill:#FFFF00,stroke:#333,stroke-width:2px style Z3 fill:#FF4500,stroke:#333,stroke-width:2px end subgraph Legend L1[Good SNR >25dB] --Green--> L2[Marginal SNR 16-24dB] --Yellow--> L3[Poor SNR style L1 fill:#7CFC00,stroke:#333,stroke-width:1px style L2 fill:#FFFF00,stroke:#333,stroke-width:1px style L3 fill:#FF4500,stroke:#333,stroke-width:1px end
10 more free samples are waiting
Create a free account to unlock the whole CWDP-305 sample bank, or get full access to all 300 practice questions in the simulator.